A commercial garlic drying machine (also searched as a garlic dryer or a food dehydrator for garlic) is used to produce dehydrated garlic slices, granules, and powder at plant scale. Airtek heat-pump garlic dryer machines are specified for food processors who need even slice color, a checked moisture endpoint, and a repeatable batch—not a home kitchen recipe.

This page outlines the usual commercial process around a garlic drying machine, from raw-bulb preparation through heat-pump drying. Figures given below come from common plant practice on the current page and should be validated against your raw material, hygiene plan, and finished-product specification.

Request a project estimate

What a commercial garlic dryer is used for

Dried garlic products are mainly divided into dehydrated garlic slices, garlic granules, and garlic powder. Most industrial lines slice peeled cloves, dry the slices in a heat-pump chamber, then mill or grade the dried slices if granules or powder are required.

Cabinet dryers suit trials, smaller lots, and frequent changeovers. Multi-trolley batch rooms suit larger daily wet infeed. See cabinet food dryer machines, batch tray heat pump dryers, and drying solutions. Related crop notes also sit under herbs & spices.

Process steps around a garlic drying machine

The notes below describe a typical commercial line. They are a conversation aid for plant buyers, not a fixed recipe and not a substitute for your food-safety plan.

1. Selecting and preparing raw garlic

Preparation usually includes selecting bulbs, cutting stems, splitting bulbs into cloves, peeling, and a further sort. Manual selection is still common at the start: bulbs are spread on a selection table so insect-damaged, moldy, or undersized heads can be removed. Very small bulbs tend to produce undersized slices after cutting, which can hurt finished grade.

After stems are cut, bulbs are often lifted into a splitting machine. A common design uses two rubber belts running at different speeds to rub the bulb apart into cloves.

2. Separating skins and peeling cloves

After splitting, cloves and loose outer skins are mixed. A blower is often used at this stage: cloves are heavier than skins, so air can take much of the skin away. Skins that remain are picked out by hand.

Cloves still carry a tight inner skin. Many plants use a dry-peeling machine: the clove is warmed until the skin loosens, then high-pressure air blows away the coat and the thin membrane on the clove. Working pressure and temperature for the peeler are set from experience with the raw lot. A range often cited in plant practice is about 9–11 kgf/cm² and 45–50°C; use your own machine manual and trials, not those figures as a universal setting. After the automatic peel, cloves are sorted again so moldy or sugared cloves, and any still unpeeled pieces, can be removed or sent back.

3. Washing, disinfecting, and slicing

Peeled cloves pick up dust and should be washed before dehydration. In a typical washer, air bubbles agitate the cloves, skins float, and cloves sink so remaining skins can be lifted off. High-pressure spray nozzles at the discharge end give a further rinse.

Some plants then hold cloves in a sodium hypochlorite solution before a clean-water rinse and drain. Concentrations, water temperature, and hold time belong in your hygiene plan; do not copy a published example as a finished SOP.

Sliced thickness drives drying quality. Cloves are usually fed to a slicer in a steady, moderate stream. In typical practice the knife disc runs at about 80–100 revolutions per minute, and slice thickness is held around 1.5–1.8 mm, with a smooth surface and few fragments or wedge-shaped pieces. After drying, thick slices can yellow and thin slices can become brittle, so blade sharpness and feed control matter.

Cut slices often go through a second bubble wash (a few minutes in cool water is common) to remove surface mucus and sugars, then a centrifuge to take off surface water and shorten dryer time. Plants often load slices in a water-permeable bag so the basket does not throw loose slices. A loading and spin example sometimes used in production is about 25–30 kg per cycle, around 1200 rpm, for roughly 30 seconds—again, check against your centrifuge and product quality.

4. Drying in the garlic dryer

Dehydrated garlic slices are dried in a dedicated heat-pump garlic drying machine. Slices are spread evenly on trays, the trays are loaded on trolleys, and the trolleys are pushed into the drying room before the unit is started.

In typical plant practice, chamber temperature is held in a range around 55–75°C, and a batch may run about 10–12 hours. A common finished-slice standard is a normal slice shape, a pale color, and moisture around 4–5%. Those targets should be proven on your slice thickness and specification. After drying, remaining skins can be removed by winnowing.

Dried slices can still differ slightly in moisture because of size variation. Many plants then rest the product for moisture equalization—for example, bagging the slices, closing the bags, and holding them on racks for about three days—before milling or packing.

How to inquire about a garlic dryer

Tell us the product form (slices, granules, or powder), wet infeed per batch or per day, slice thickness if already fixed, target moisture and color, and site power. Airtek will recommend a heat-pump cabinet or trolley garlic drying machine from the existing series.

Request a project estimate

Call Us Now!